With the exploration and innovation of company people, gradually formed four major advantageous products: steel plate, steel pipe, stainless steel, special steel.
AISI 4130 steel can be annealed at 843C (1550F) followed by air cooling at 482C (900F). Tempering of AISI 4130 steel can be performed at 399 to 566C (750 to 1050F), depending on the desired strength level.
It is very useful for any mechanical engineer to be aware of 4130 steel properties. 4130 steel, otherwise known as Chromoly or chromium molybdenum steel alloy, is made with 0.8 to 1.1% chromium and 0.15 to 0.25% molybdenum as strengthening agents. steel properties make it a versatile metal, especially mechanical properties such as high ductility, good weldability, and the fact it can be machined easily.
AISI 4130 steel is usually supplied as round bar commonly in the hardened and tempered condition. AISI/SAE 4130 steel grade is a versatile alloy with good atmospheric corrosion resistance and reasonable strength up to around 315 C (600 F).
AISI 4130 Astm, AISI 4130 Yield Strnght, AISI 4130 Steel, AISI 4130 Hardness, AISI 4130 Specs, AISI 4130 Sheet, AISI 4130 Standard, AISI 4130 Steel Eqtivalent, AISI 4130 Steel Tube, AISI 4130 Steel Compoaition,AISI 4142, AISI 4145, AISI 4140 Properties, AISI 4140 Ht, AISI 4140 Hardness, AISI 4140 Alloy Steel, AISI 4140 Mechanical Properties 4130 steel properties yield strength
Chemical Properties. The chemical properties of 4130 and 4140 steel are similar aside from differences in Carbon and Manganese concentrations. Carbon, C 0.30% 0.40% Manganese, Mn 0.40-0.60% 0.75-1.00% Chromium, Cr 0.80-1.10% 0.80-1.10% Molybdenum, Mo 0.15-0.25% 0.15-0.25%.
SAE-AISI 4130 steel is an alloy steel formulated for primary forming into wrought products. 4130 is the designation in both the SAE and AISI systems for this material. G41300 is the UNS number. The properties of SAE-AISI 4130 steel include four common variations. This page shows summary ranges across all of them.
This process occurs in steel when it is worked, machined or heated. When 4130 is heated and held at 1,525 degrees, the crystalline structure of the steel begins to revert back to a malleable state. Fully annealed 4130 has a tensile strength of 81,200 pounds per square inch and a Rockwell hardness of 95.
A very common general purpose grade of medium carbon, Cr-Mo steel. Flexibility afforded by heat treatment options allows it to attain a range of toughness and strength values. Good hardenability, strength, wear resistance, toughness, and ductility.
The Table chart below gives typical mechanical characteristics for selected properties. For all critical applications, verify to the applicable industry or requisite material / steel standard. AISI Carbon Steel Mechanical Characteristics Table Chart
Offers good strength, and weldability without compromising steel abrasion and impact resistance. Easy to machine and hot work as well as cold work in the annealed state, it becomes significantly more challenging once the steel is hardened. 4130 steel can also be easily welded.
AISI 4140 alloy steel is a chromium-, molybdenum-, and manganese-containing low alloy steel. It has high fatigue strength, abrasion and impact resistance, toughness, and torsional strength. The following datasheet gives an overview of AISI 4140 alloy steel.
Alloy 4130 is tempered at between 750 F and 1050 F, depending upon the strength level desired. The lower the tempering temperature the greater the strength. Hardening. Hardening is accomplished by heat treatment or by cold working see Heat Treatment. Other Comments. The 4130 alloy is a through hardening alloy and should not be case hardened.
There are 31 material properties with values for both materials. Properties with values for just one material (5, in this case) are not shown. For each property being compared, the top bar is AISI 316 stainless steel and the bottom bar is annealed SAE-AISI 4130.
4130 has improved weldability compared to 4140 (which has a higher carbon level) though this is achieved at the expense of through thickness strength. Available in bar dimensions of 50.8 mm (2") to 762 mm (30") Length range up to 9.14 m (30')
4130 This low alloy steel contains high amounts of chromium and is often referred to as chromoly. 4130 steel has good machinability, ductility, weldability and strength characteristics. It is used for many different industries including the automotive, aerospace and machining industries. 4340
Alloy 4130 is a widely used Aircraft Steel due to its weldability, ease of fabrication and mild hardenability. The hardenability and weldability of Alloy 4130 are considered equivalent to 8630 (MIL-S-6250) . Alloy 4130 is also vacuum degassed to meet the magnetic particle inspection standards of AMS 2301. Typical Mechanical Properties
Materials Alloys Steel Alloy Steel AISI 8630H Materials Alloys Aluminum Alloy Cast A360.0 Materials Alloys Copper Alloy Wire AWG-17
4130 Alloy Steel Properties, 4130 Alloy Steel Composition, 4130 Alloy Steel Physical Properties, 4130 Alloy Steel Mechanical Properties, 4130 Alloy Steel Density, 4130 Alloy Steel Chemistry, 4130 Alloy Steel Electrical Resistivity
TimkenSteels 4130HW steel is a fine-grained, low-alloy steel that offers optimum heat-treat response in heavier . cross-sections. It is used in a variety of bar and tubing applications in quenched/tempered conditions. Yield strengths range from 80 ksi through 95 ksi but may be tempered to higher strength levels.
AISI or SAE 4130 grade is a low-alloy steel containing chromium and molybdenum as strengthening agents. The steel has good strength and toughness, weldability and machinability. AISI/SAE 4130 grade is a versatile alloy with good atmospheric corrosion resistance and reasonable strength.
Typical 4130 Seamless Mechanical Steel Tubing Facts: Cold Working As a result of its properties, cold working by conventional methods is common with this alloy. Annealing Furthermore, 4130 is annealable at 1550 F for a time long enough to allow thorough heating of the section size.
41xx steel is a family of SAE steel grades, as specified by the Society of Automotive Engineers (SAE). Alloying elements include chromium and molybdenum, and as a result these materials are often informally referred to as chromoly steel (common variant stylings include chrome-moly, cro-moly, CrMo, CRMO, CR-MOLY, and similar).
Known for its good mix of strength, ductility and hardness, 1018 steel is a mild, low-carbon steel. This alloy of steel has a small percentage of manganese to help achieve these properties. While other steels can exceed its mechanical properties, 1018 steel is more easily manufactured and machined, reducing its cost.
4130 Annealed Steel Bar, Rod & Wire. Minimum Properties. Tensile Strength, psi. 81,200. Yield Strength, psi. 52,200. Elongation. 28.2%. Rockwell Hardness. B82. Chemistry. Iron (Fe) 97.3 - 98.22%. Carbon (C) 0.28 - 0.33%. Chromium (Cr) 0.8 - 1.1%. Manganese (Mn) 0.4 - 0.6%. Molybdenum (Mo) 0.15 - 0.25%. Phosphorus (P) 0.035% max. Sulphur (S) 0.04% max. Silicon (Si) 0.15 - 0.35%
information,mechanical properties, physical properties, mechanical properties, heat treatment, and Micro structure, etc. It also contains the use of SAE 4130,such as it is commonly used in bars, sheet,plates, steel coils, steel pipes,forged and other materials application. Datasheet for Steel Grades Carbon Steel SAE 4130 SAE 4130 Standard Number:
This page cover the AISI 4130 chemical element, Mechanical Properties, AISI 4130 Datasheet, Cross Reference of AISI 4130 steel, Mainly used for .
guide to (1) those properties that may normally be expected from a particular grade of steel and (2) the treatment to use in order to obtain the desired properties. MecHAnicAL PRoPeRtieS The mechanical properties (tensile strength, yield point, etc.) shown herein are the results of actual tests performed as follows: carbon Steels .
TimkenSteels 4140HW grade is a fine-grained, low-alloy steel that offers optimum heat-treat response in heavier cross-sections. You find 4140HW in a variety of bar and tubing applications in quenched and tempered conditions. Yield strengths range from 110 ksi through 140 ksi, but we can temper it to other strength levels.
4130 has improved weldability compared to 4140 (which has a higher carbon level) though this is achieved at the expense of through thickness strength. Available in bar dimensions of 50.8 mm (2") to 762 mm (30")
4130 steel properties yield strength chart aisi 4130 steel properties 4130 steel properties yield strength calculator 1018 steel properties 4130 steel properties yield strength formula aisi 4130 steel equivalent 4130 steel properties yield strength scale 4130 steel properties density
You may also leave contact information, we will contact you as soon as possible!