1045 steel composition

1045 steel composition

With the exploration and innovation of company people, gradually formed four major advantageous products: steel plate, steel pipe, stainless steel, special steel.

  1. AISI 1045 Medium Carbon Steel - AZoM.com

    AISI 1045 steel is a medium tensile steel supplied in a black hot-rolled or normalized condition. It has a tensile strength of 570 - 700 MPa and Brinell hardness ranging between 170 and 210. AISI 1045 steel is characterized by good weldability, good machinability, and high strength and impact properties in either the normalized or hot-rolled condition.

  2. 1018 vs. 1045 Steel Comparison | Capital Steel & Wire

    A carbon steel like 1330 for example has a much higher concentration of manganese. The carbon content is what really separates the chemical composition of 1018 and 1045, with 1045 steel having a higher carbon composition. Mechanical Properties. Whether steel is cold drawn or hot rolled plays a huge factor in the mechanical properties of steel.

  3. What is 1045 / S45C / C45 Steel Properties Chemical 1045 steel composition

    1045 steel is widely used for the industry application that required higher strength and wear resistance than low-carbon steel. And the typical applications are gears, shafts, rolls, crankshafts, sockets, bolts and etc.

  4. ASTM SAE AISI 1045 Carbon Steel Heat Treatment, Chemical 1045 steel composition

    ASTM SAE AISI 1045 steel is one of the commonly used medium carbon steels with an average carbon content of 0.45%, medium tensile properties, good strength, toughness and wear resistance. It can be treated by annealing, flame treatment or induction hardening. C1045 is also known as 1045 cold rolled steel (cold worked), and 1045 hot rolled steel is known as 1045 HR.

  5. 1045 steel - Steel grades, Properties and Global Standards

    Stainless Steel, Special Steel, Compressor Blading, Turbine Blading, Superalloy Supplier. 1045 can be supplied as steel plate/ sheet, round steel bar, steel tube/pipe, steel stripe, steel billet, steel ingot, steel wire rods. electroslag, forged ring/ block,etc.

  6. 1045 Steel Composition - Image Results

    1045 Steel Composition images

  7. AISI 1045 Medium Carbon Steel - steelforge.com

    General characteristics of Carbon Steel 1045. C1045 is a medium carbon, medium tensile steel supplied as forged or normalized. This steel shows reasonable strength and toughness. C1045 will through harden to 2.5 (63mm) with a tensile strength of 66-120 Ksi (620-850 MPa) C1045 is a versatile medium carbon engineering steel1045 steel composition

  8. AISI 1045 Steel | SAE-AISI 1045 (S45C, G10450) Carbon Steel 1045 steel composition

    AISI 1045 Steel is medium tensile steel supplied in the black hot rolled or normalized condition. It exhibits good weldability, good machinability, and high strength and impact properties to be used in various industrial applications.

  9. AISI 1045 Steel, cold drawn, high temperature stress relieved 1045 steel composition

    AISI 1045 Steel, cold drawn, high temperature stress relieved, 50-75 mm (2-3 in) round Categories: Metal; Ferrous Metal; Carbon Steel; AISI 1000 Series Steel; Medium Carbon Steel. Material Notes: Respond to heat treatment, and flame and induction hardening, but not recommended for carburizing or cyaniding.

  10. 1045 Medium Tensile Carbon Steel Bar | Interlloy 1045 steel composition

    1045 is a medium tensile low hardenability carbon steel generally supplied in the black hot rolled or occasionally in the normalised condition, with a typical tensile strength range 570 - 700 Mpa and Brinell hardness range 170 - 210 in either condition.Characterised by fairly good strength and impact properties, plus good machinability and reasonable weldability in the hot rolled or normalised condition.

  11. ASTM SAE AISI 1018 Carbon Steel Chemical Composition 1045 steel composition

    AISI SAE ASTM 1018 steel has many semifinished and final products such as round bar, flat bar, steel tubing and pipes, etc. 1018 carbon steel is versatile and is commonly used in a variety of carburized parts such as gears, pinions, ratchets, worms, pins, chain pins, pins, machine parts, tools and mold components.

  12. 1045 MEDIUM TENSILE CARBON STEEL BAR - interlloy.com.au

    1045 medium tensile carbon steel bar 1045 is a medium tensile low hardenability carbon steel generally supplied in the black hot rolled or occasionally in the normalised condition, with a typical tensile strength range 570 - 700 Mpa and Brinell hardness range 170 - 210 in either

  13. 1040 vs 1045 Steel Comparison | Capital Steel & Wire

    A comparison of the chemical and mechanical properties of 1040 and 1045 grade steel. Hot rolled and cold drawn statistics are used to distinguish 1040 vs 1045 steel grades. Both 1040 and 1045 steels are popular at Capital Steel & Wire, and both have different chemical and mechanical characteristics.

  14. SAE-AISI 1045 (S45C, G10450) Carbon Steel :: MakeItFrom.com

    SAE-AISI 1045 steel is a carbon (non-alloy) steel formulated for primary forming into wrought products. 1045 is the designation in both the SAE and AISI systems for this material. G10450 is the UNS number. It can have a moderately high tensile strength among the wrought carbon or non-alloy steels in the database.

  15. AISI 1045 Carbon Steel (UNS G10450) - azom.com

    AISI 1045 can be formed into turned, ground and polished bars that can be machined unsymmetrically with limited distortion. The following sections will discuss in detail about AISI 1045 carbon steel. Chemical Composition. The chemical composition of AISI 1045 carbon steel is outlined in the following table.

  16. Properties of 1045 Steel | Sciencing

    This is steel that has been given a heat treatment, intended to bring many samples under consideration into the same condition. 1045 is known for fairly good strength and impact properties. It has good machinability qualities as well as serviceable welding qualities, whether in the rolled or normalized condition.

  17. MEDIUM TENSILE STEEL AISI 1045 - S&T Stainless

    MEDIUM TENSILE STEEL AISI 1045 AISI 1045 Medium Carbon, Medium Tensile Steel, supplied black as rolled, black as forged or normalised and bright drawn or smooth turned, offering good strength, toughness and wear resistance. Will through harden in sections up to 63mm with a tensile strength of 620 - 850 MPa. TYPICAL APPLICATIONS:

  18. ASTM A36 Carbon Steel vs. SAE-AISI 1045 Steel :: MakeItFrom.com

    Both ASTM A36 carbon steel and SAE-AISI 1045 steel are iron alloys. They have a very high 99% of their average alloy composition in common. There are 31 material properties with values for both materials. Properties with values for just one material (1, in this case) are not shown.

  19. 1045 medium tensile carbon steel in AISI Standard

    The Chemical Composition of 1045 Mild Steel: Chemical alloying compositions are explicated below. Maximum percentage of Carbon as defined in the standard is 0.5 whereas Minimum percentage of Carbon as defined in the standard is 0.42; Maximum percentage of Manganese as defined in the standard is 0.9

  20. Carbon steel SAE 1045 [SubsTech]

    to Carbon steels to Properties of steels and cast irons carbon_steel_sae_1045.txt Last modified: 2012/06/02 by dmitri_kopeliovich Except where otherwise noted, this work is licensed under a Creative Commons Attribution-Noncommercial-Share Alike 3.0 License

  21. 1045 Steel - 1045 Steel Composition in Samurai Swords

    1045 Steel 1045 Steel Composition One of the most commonly use materials in the world when it comes to decorative blades and swords is 1045 steel. This simply means the steel is a plain carbon steel with 0.45% carbon content.

  22. 1045 Steel Bars and Rods | Clifton Steel

    1045 steel round bars are special turned, ground, and polished steel designed for applications calling for a steel superior to cold rolled or hot rolled bars, but at an economical price. 1045 round bars are produced to exacting specifications to assure close tolerances in diameter, straightness and concentricity.

  23. Atlas 1045 Medium Tensile Carbon Steel Bar 1045

    Medium Tensile Carbon Steel Bar 1045 Colour code: Jade Green Introduction Atlas 1045 is a fully killed plain carbon steel product containing nominally 0.45% carbon. This grade was formerly designated as K1045. Atlas 1045 is supplied based on it meeting specified chemical composition requirements only. Related Specifications

  24. C45 Round Bar | AISI 1045 | DIN 1.1191 - Otai Special Steel

    Steel C45 Round Bar is an unalloyed medium carbon steel, which is also a general carbon engineering steel. C45 is a medium strength steel with good machinability and excellent tensile properties. C45 is a medium strength steel with good machinability and excellent tensile properties.

  25. Cold Rolled Steel C1045 | Metal Supermarkets - Steel 1045 steel composition

    Cold Rolled Steel C1045. Grade Description: A medium carbon steel allowing higher strength properties than 1018. A wide range of properties can be obtained.

  26. 1045 CF Bar | Alro Steel

    1045 CF is a medium carbon steel used extensively in induction hardening applications. It can be forged satisfactorily and is the most common shafting steel in the medium carbon range. Due to its carbon content, 1045 CF bar is only fair for welding or brazing.

  27. 1045 Steel | JIS S45C | DIN CK45 | EN8 - OTAI Special Steel

    AISI 1045 steel / JIS S45C / DIN CK45 Carbon steels also called carbon element. They are a category of steels with 0.12 to 2% carbon composition. AISI 1045 steel is a kind of medium carbon steel design need more intensity and hardness can function.

  28. 1045 Cold Drawn (CD) Steel Bar Suppliers | Eaton Steel Bar 1045 steel composition

    1045 Cold Drawn Steel Bar. Cold rolled 1045 steel bar is a medium carbon steel grade with good weldability, formability, and better mechanical properties over other cold drawn grades. This grade is widely available and commonly stocked because of its excellent properties and cost.

  29. AISI 1045 Steel, cold drawn, high temperature stress relieved 1045 steel composition

    Property Data; This page displays only the text of a material data sheet. To see MatWeb's complete data sheet for this material (including material property data, metal compositions, material suppliers, etc), please click the button below.

  30. 1045 Hot Rolled Steel Supplier - 1045 Steel Properties 1045 steel composition

    1045 Hot Rolled SBQ Bar. HR 1045 steel bar is a medium-carbon common steel grade with good weldability, higher strength, and impact properties for a variety of applications. 1045 steel is a widely available, common grade because of its cost and excellent properties.

  31. Also Try

    1045 steel composition chart 1045 steel properties 1045 steel composition calculator 1060 steel 1045 steel composition definition 1045 steel tubing 1045 steel composition sheet 1045 steel wikipedia

Message

You may also leave contact information, we will contact you as soon as possible!

Messages
Henan BEBON Iron & Steel Co., Ltd
Tel : 0086-371-86151827
E-Mail : [email protected]
address : Xicheng Science & Technology Building High-tech Development Zone, Zhengzhou, China