With the exploration and innovation of company people, gradually formed four major advantageous products: steel plate, steel pipe, stainless steel, special steel.
AISI 4140 alloy steel is annealed at 872C (1600F) followed by slowly cooling in the furnace. Tempering. AISI 4140 alloy steel can be tempered at 205 to 649C (400 to 1200F) depending upon the desired hardness level. The hardness of the steel can be increased if it has a lower tempering temperature.
SAE 4140 (AISI 4140 steel) is a Cr-Mo series (Chrome molybdenum series) low alloy steel, this material has high strength and hardenability, good toughness, small deformation during quenching, high creep strength and long-lasting strength at high temperature.
Chemical composition and properties of european equivalents (EN) for 4140 (USA, AISI, ASTM, UNS): 42CrMoS4 (1.7227) , 42CrMo4 (1.7225) , 4140 (USA, AISI, ASTM, UNS ) - European (EU, EN) and wordwide Steel equivalent grades These comparison table is only intended as an indication of the closest khown equivalent grades.
AISI 4140 alloy steel is annealed at 872C (1600F) followed by slowly cooling in the furnace. Tempering AISI 4140 alloy steel can be tempered at 205 to 649C (400 to 1200F) depending upon the desired hardness level. The hardness of the steel can be increased if it has lower tempering temperature.
The following datasheet gives an overview of AISI 4140 alloy steel. 4140 alloy steel material is a high quality Quenched and Tempered Alloy Structural steel, It belong to the high quality medium carbon alloy steel, Oil Quenched & Tempered Hardenss is 28-34 HRC.4140 Annealing delivery hardenss less than 250HB.
Heat Treatment of SAE/AISI 4140 Alloy Steel / 42CrMo4 steel 4140 Steel Annealing Slowly heat to 8008500 C, keep enough time, ensure heat thoroughly. then cooling in furnace to 480 C, then cool in air.
AISI 4140 Alloy Steel is chromium, molybdenum, and manganese containing low alloy steel. It has high fatigue strength, toughness, abrasion resistance, and torsional strength. AISI 4140 is 1% chromium molybdenum medium harden the capability basic cause excessive tensile metal.
Equivalent Grades ALLOY STEEL Equivalent Grades Internal Standard BS DIN IS EN SAE/AISI EN18 530A40 37Cr4 40Cr1 EN18 5140 EN24 817M40 34CrNiMo6 40NiCr4Mo3 EN24 4340 EN19C 709M40 - 40Cr4Mo3 EN19C 4140,4142 EN19 709M40 42Cr4Mo2 40Cr4Mo3 EN19 4140,4142 EN18D 530A40 37Cr4 40Cr1 EN18D 5140
AISI or SAE 4130 grade is a low-alloy steel containing chromium and molybdenum as strengthening agents. Forging of this steel should be carried out between 2200 and 1650 F (1200 and 900 C). This alloy finds many applications for the aerospace and oil and gas industries, along with uses the automotive, agricultural and defense industries
Hardening of AISI Alloy Steel 4140. SAE 4140 alloy steel is usually supplied ready heat treated to hardness in 18-22 HRC. If further heat treatment is required, then heat to 840 oC 875 oC, hold until temperature is uniform throughout the section, soak for 10 15 minutes per 25 mm section, and quench in oil, water, or polymer as required.
AISI 4140 steel is a low alloy steel containing chromium, molybdenum, and manganese. It is widely used across numerous industries and is an excellent material choice due to its toughness, high fatigue strength, and abrasion and impact resistance. Not many grades can match the versatility and usefulness of 4140.
steel round bar; What is 4140 Steel? AISI 4140 steel also can be called DIN 1.7225 and JIS SCM440 steel. 4140 alloy steel has high fatigue strength and low notch sensitivity. Low-temperature impact toughness is also very high, no obvious temper brittleness. It is mainly used after quenching and tempering state.
Typical Properties. AISI 4140 and 4150 is a medium carbon, chromium-molybdenum alloy steel. This steel is offered in a wide range of conditions including but not limited to: cold drawn annealed, hot roll heat treated, heat treated turned ground and polished.
Steel Grade Equivalent Table (EN, SAE/AISI, UNS, DIN, BS, UNI, JIS) The table below compares common grades of materials from various international specifications. Note that materials compared are the nearest available grade and may have slight variations in actual chemistry.
LSS 4140 and 4142HT Alloy Steels. LSS 4140 is the classic AISI 4140 alloy steel that is sold in the annealed condition at a hardness less than or equal to 217 HBW. LSS 4142HT is a similar steel which is sold prehardened to 28 to 32 HRC (269 to 302 HBW). Pieces of LSS 4142HT that are greater than about 3 inches4140 alloy steel equivalent
AISI 4140 steel stockholders and suppliers, delivering to the whole of the UK. AISI 4140 is a chromium molybdenum alloy steel specification widely used in the oil and gas industry. Similar to grade AISI 4130 but with a slightly higher carbon content.
Do you need custom fasteners created with Alloy Steel Grade 4140? Since our inception, Elgin Fastener Group has met every challenge of providing Quality, Timely, Cost-effective solutions for specialty fastener applications.
4140 is a 1% chromium - molybdenum medium hardenability general purpose high tensile steel - generally supplied hardened and tempered in the tensile range of 850 - 1000 Mpa (condition T).4140 is now available with improved machinability, which greatly increases feeds and/or speeds, while also extending tool life without adversley affecting mechanical properties.
prosaic steel & alloys is highly acclaimed manufacturer, exporter, supplier, stockholder, distributor, stockholder of aisi 4140 pipe, aisi 4140 seamless pipes, astm a519 4140 pipes, a519 4140 alloy steel seamless pipes, aisi 4140 grade l80 alloy steel pipes, aisi 4140 seamless tubes, prosaic steel and alloys, india.
EN19 Steel is one steel grade in BS 970-1955 standard, which is specification for wrought steels for mechanical and allied engineering purpose. Although there is new version of BS 970-1996 latest edition. And EN19 steel grade is similar to 709M40 grade in new version. The EN19 steel equivalent grades are AISI 4140, DIN 1.7225/ 42crmo4. There 4140 alloy steel equivalent
AISI 4140 is a chromium-molybdenum alloy steel. The chromium content provides good hardness penetration, and the molybdenum content ensures uniform hardness and high strength. AISI 4140 chrome-molybdenum steel can be oil hardened to a relatively high level of hardness. The desirable properties of 4140 alloy steel equivalent
HIGH TENSILE STEEL AISI 4140 AISI 4140 Chrome - Moly High Tensile Steel, generally supplied hardened and tempered to Condition T in sections up to 100mm, with a tensile strength of 850 1000 MPa and aiming for this strength range in larger sections. It offers a very good balance of strength, toughness and wear-resistance.
4140 HIGH TENSILE STEEL 4140 is a 1% chromium - molybdenum medium hardenability general purpose high tensile steel - generally supplied hardened and tempered in the tensile range of 850 - 1000 Mpa (condition T).4140 is now available with improved
Table of Steel Equivalent Grades (EN, SAE/AISI, UNS, DIN, BS, UNI, JIS) The table below compares steel equivalent grades of materials from various international specifications. Note that materials compared are the nearest available grade and may have slight variations in actual chemistry.
Superior Steel Alternative to. 4140 Alloy Steel. Pennsylvania Steel Corporation presents an alternative to SAE 4140 alloy steel. FLEXOR's chemistry and mechanical properties are comparable, if not superior to 4140 alloy steel and thusly, can be utilized in most of the same applications.
4140 Alloy Steel Round, is an cold drawn annealed steel of relatively high hardenability with its chromium content provides good hardness penetration, and the molybdenum imparts uniformity of hardness and high strength. 4140 Alloy Steel Round responds well to heat-treatment and is relatively easy to machine in the annealed condition. 4140 Alloy Steel Round has good strength and wear resistance 4140 alloy steel equivalent
Buy alloy-steel-round-tube-4140 and other metal-working products online at OnlineMetals.com.
42CrMo steel is a Chinese alloy steel, and has high strength and toughness, good hardenability, and no obvious temper brittleness. After quenching and tempering treatment, it has high fatigue limit and resistance to multiple impacts, and good low temperature impact toughness.
Alloy Steel Round Bar 4140 Annealed Cold Finish, also referred to as Chromoly Steel, is known for strength, resistance to fracturing, abrasion, and impact in high stress applications. 4140 is popular for a wide range of applications and is ductile and easily machined in the annealed state.
Alloy 4140 is an oil-hardening steel of relatively high hardenability. Its chromium content provides good hardness penetration, and the molybdenum imparts uniformity of hardness and high strength. C4140 responds well to heat-treatment and is comparatively easily machined in the heat-treated condition.
You may also leave contact information, we will contact you as soon as possible!